Dimplex Ignite Evolve Size Guide

This guide covers the framing dimensions, electrical requirements, and installation specifications for the Dimplex Ignite Evolve Linear Electric Fireplace. It is a technical reference for the four available size variants: 50", 60", 74", and 100". All values are sourced from the Dimplex installation manual.

The Ignite Evolve is a recessed linear electric fireplace that installs into a framed wall opening. It supports two wall depths — a 2x4 partially recessed configuration and a 2x6 flush-mounted configuration — and is approved for both indoor and outdoor use in sheltered locations. All four size variants share the same framing height, framing depth, and electrical specifications. Only the framing width and viewing area width differ between models.

If you are deciding between the Ignite Evolve and another Dimplex linear series, the Ignite Evolve's distinguishing installation characteristics are its 3-1/2" minimum framing depth (compatible with a standard 2x4 partition wall), its four size options ranging from 50" to 100", and its outdoor-certified rating. For a full comparison of all Dimplex linear fireplaces, see the Dimplex Electric Fireplace Comparison Guide.

The Ignite Evolve supports two recessed wall configurations. The framing width and height of the rough opening are the same for both; only the required wall depth differs.

The fireplace installs partially recessed into a standard 2x4 stud wall. The framing depth required is 3-1/2". Because the unit depth (5-3/4") exceeds the 2x4 framing depth, the front face of the fireplace will protrude from the finished wall surface. The optional XLFTRIM kit (sold separately, model number varies by size) is recommended for this configuration to accommodate the protruding portion.

The fireplace installs fully flush with the finished wall surface in a 2x6 stud wall. The framing depth required is 5-1/2". The included trim can be used with drywall and tile finishes. For stone, brick, and other solid finish materials, the trim is not required — the unit installs directly against the face of the finish material.

The electrical specifications are the same for all four Ignite Evolve models. The unit supports both 120V and 240V operation. Heat output differs between the two configurations; framing dimensions do not change based on voltage selection.

The unit is cULus listed (file E71416) and meets UL-2021 and CSA C22.2 No. 46 standards. No venting or gas line is required.

Specific numeric clearance values for the top, sides, rear, and bottom of the unit are not printed in the installation manual documents provided. The installation manual instructs installers to follow the manufacturer's guidelines for minimum clearances to combustibles, walls, and finishes. Confirm the applicable clearance requirements in the full Dimplex Ignite Evolve owners manual before framing and finishing.

For any temperature-sensitive object mounted above the fireplace — including televisions, mantels, and artwork — follow the installation recommendations provided by that object's manufacturer for placement over a heater.

The Dimplex installation manual documents three temperature zones above the unit using a chart referenced as Figure 1:

• Areas subject to temperatures greater than 65°C (149°F)
• Areas subject to temperatures greater than 40°C (104°F)
• Areas subject to temperatures less than 40°C (104°F)

The zone a specific overhang falls into depends on the combination of overhang height (distance above the top of the unit) and overhang depth (horizontal projection). Consult Figure 1 in the Dimplex installation manual to determine the temperature zone for your specific configuration before mounting any temperature-sensitive object above the fireplace.

The Ignite Evolve is certified for installation in outdoor areas that are sheltered by an overhead structure protecting against direct water ingress. Installation on a ground-fault protected circuit is recommended. All electrical connections must comply with local building code requirements.

To maintain warranty coverage, the overhead structure must meet this rule: the maximum height from the bottom of the fireplace to the underside of the overhead structure must be no greater than three times the horizontal projection length of that structure.

• Maximum height is measured vertically from the bottom of the fireplace to the bottom edge of the overhang
• Projection length is measured from the exposed face of the fireplace to the parallel edge of the overhang
• The overhang must clear at least 24" above the bottom of the fireplace and project at least 5" from the face of the unit

Example from the installation manual: if the overhang is 9 feet above the bottom of the fireplace, it must extend at least 3 feet outward on all sides.